Products - GPM32FD0118B

General Description

The GPM32FD0118B series of industrial microcontroller is based on the ARM® Cortex®-M0 processor core and operates at a frequency of up to 92MHz. The GPM32FD0118B series devices are optimized for motor control, power conversion, home appliances and general purpose applications.  GPM32FD0118B operates in the -40°C to 105°C temperature range from 2.3V to 5.5V wide voltage supply.

Features

• CPU Subsystem
  • CPU Core
    • ARM^® Cortex^®-M0 32-bit CPU (92MHz max) with Code Fetch Accelerator
    • Nested Vectored Interrupt Controller (NVIC) with 32 interrupt sources
    • 24-bit SysTick timer
    • Single cycle 32bit multiplier instruction
  • MATH Co-processor (MATH)
    • 24-bit trigonometric calculation (CORDIC)
    • Hardware Divider
• Memories
  • 8K bytes SRAM (Up to 12KB is configurable)
  • 4K bytes System Memory for loader
  • 60K bytes (max) Program Memory
    • Configurable Data Memory supported
• Clock Management
  • Internal oscillator: 8MHz±5%@ 2.3V~5.5V / -40°C~105°C
  • Internal oscillator: 32KHz±50%
  • Phase Lock Loop : 92MHz(max)
    • The PLL output frequency based on M/N Coefficient
• Power Management
  • In SLEEP mode: Only the CPU stopped.
  • In DEEPSLEEP mode: All clocks are stopped.
• Reset Management
  • Power On Reset (PORRESETn)
  • PAD Reset (PADRESETn)
  • Master Reset (MRESETn)
  • System Reset (SRESETn)
• Analog peripherals
  • Up to two A/D Converters with 1M SPS and 16 analog inputs
  • Up to two fast Analog Comparators (ACMP)
  • Up to four Operational Amplifier (OPA)
    • With Unity gain frequency 20 MHz
    • Differential or Single input available
  • Die Temperature Sensor
  • Low Voltage Reset (2.1V, 2.7V, 3.2V, 4.2V)
  • Low Voltage Detector (2.4V, 2.9V, 3.4V, 4.4V)
• Industrial Control Peripherals
  • 16-bit Capture/Compare/PWM Units 4 (CCU4)
  • 16-bit Enhance Capture/Compare/PWM Units 6 (eCCU6)
    • For motor control and power conversion
  • 24-bit Position Interfaces (POSIF)
    • For hall and quadrature encoders and motor positioning
• System Control
  • Up to 8 channels DMA controller
    • Support peripheral : Timers, eCCU6, CCU4, ADCs, I²Cs, UARTs
  • Watchdog Timer (WDG) for safety sensitive applications
  • System Management Unit (SMU) for system configuration and control
  • 96-bit Unique ID
• I/O Ports
  • 24 fast multifunction bi-directional I/Os
    • All I/Os support external interrupt vectors
    • Built-in pull-up/pull-down resistor
    • I/O ports with 15mA/20mA source/sink current
• Timer
  • Up to two 16-bit general timers
• High Side and Low Side Gate Driver
  • Built in dead time for short through protection.
  • Built in bootstrapping switch.
  • Drives three phase N-Channel MOSFET.
  • Typically Output Source / Sink current capability 1A/1A.
• Communication peripherals
  • Up to two I2C
  • Up to three UART
    • Full duplex & half duplex supported
• Security
  • Four Security Levels supported
• Debug System
  • ARM serial wire debug (SWD)
  • Four hardware breakpoints
  • Two watch points
• Operation Temperature
  • -40°C to 105°C
• Reliability
  • HBM 4KV / MM 400V / CDM 500V
• Package
  • LQFP48