Products - GPM8F3132B

General Description

The GPM8F3132B, a highly integrated microcontroller, features a pipelined 1T 8051-based CPU, 1K-byte XRAM, 256-byte IDM SRAM, and 32K-byte program FLASH memory into a single chip. It supports up to 43 programmable multi-functional I/Os, Timer0/1/A/B/C, UART0, SPI (master/slaver), I2C (master/slaver), three sets of OP, 48MHz PLL, 16-bit x 16-bit multiplier, 32-bit / 16-bit divider and two sets of 8-channle SAR ADC with 12-bit resolution for general-purpose application. It operates over a wide voltage range of 2.4V - 5.5V with variety of clock sources. It also provides one power saving mode in power management unit to manage power consumption more efficiently. Moreover, there is an on-chip debug circuit with two pins equipped to facilitate a full speed in-system debug while in application development phase.

Features

• CPU
  • High speed and high performance 1T 8051-based CPU
  • 100% software compatible with industry standard 8051
  • Pipeline RISC architecture enables to execute   instructions 10 times faster than standard 8051
  • Up to 48MHz clock operation

• Memories
  • 1K bytes XRAM
  • 256 bytes internal Data Memory (IDM) SRAM
  • 32K bytes Flash with high endurance
• Minimum 200,000 program/erase cycles
• Minimum 20 years data retention
• 1KB page size
• Programming read only level for software security
• Clock Management
  • Internal oscillator: 16MHz±2% @ 2.4V~5.5V
  • Internal oscillator with PLL : 48MHz
• Power Management
  • One Sleep mode for power saving
• Interrupt Management
  • 13 interrupt sources
  • Up to 6 external interrupt sources
• Reset Management
  • Power On Reset (POR)
  • Low Voltage Reset (LVR)
  • Pad Reset (PAD_RST)
  • Watchdog Reset (WDT_RST)
  • Software Reset (S/W_RST)
  • Flash Access Error Reset (ADDR_ERR_RST)
• Programmable Watchdog Timer
  • A time-base generator
  • An event timer
  • System supervisor
• Three OPs
• I/O Ports
  • Max. 43 multifunction bi-direction I/Os
  • Each incorporates with pull-up resistor, pull-down resistor, output high, output low , output driving capability and floating input, determined by user's settings at the corresponding registers
  • I/O ports with 12mA or 6mA current sink
  • I/O ports with 12mA or 6mA current drive
• Two 16-bit Timers/Counters (Timer 0/1)
  • Timer mode with selectable clock source
  • Auto reload 8-bit timers
• Three Powerful Timers: TimerA / TimerB / TimerC, with 16-bit Compare / Capture / PWM Unit
  • Timer mode with selectable clock source
  • Auto-reload 16-bit timers
  • Event capturing
  • Pulse width modulation and measurement
• UART0
  • One synchronous mode
  • Three asynchronous modes
• SPI (master / slaver mode)
  • Programmable phase and polarity of master clock
  • Programmable master SPI clock frequency
  • Max. SPI clock: 24MHz (F_pll /2) @48MHz
• I2C (master / slaver mode)
  • Programmable master I2C clock frequency
  • Max I2C clock: 375KHz (F_pll /128) @48MHz
• A/D Converter
  • Two 8-channel 12-bit resolution ADC
  • Control independent per set
• Built-in Low Voltage Reset
  • Trigger level: 1.9V, 2.4V, 3.2V, 4.2V
• Built-in Low Voltage Detect
  • Programmable level: 2.1V, 2.6V, 3.4V, 4.4V
• MDU
  • Built-in 16-bit X 16-bit signed multiplier
  • Built-in 32-bit / 16-bit signed divider
• On-chip Debug Unit
  • C compatible development tools