產品資訊 - GPM8F2202A

General Description

The GPM8F2202A is a highly integrated microcontroller. in addition to integrate a pipelined 1T 8051 CPU, 128 byte IDM SRAM and 2K byte program EEPROM, it also includes 14/5 programmable multi-functional I/Os, Timer0/1/2, UART, and two comparators and one up to 6/2+1 channel (6/3 channel external ADC input + 1 channel internal 1.23v) of 12-bit ADC for general-purpose application. It operates over a wide voltage range of 2.0V - 5.5V with different clock sources. It has two modes in power management unit. The details are described in the following sections.

Features

• CPU
  • High speed, high performance 1T 8051
    • 100% software compatible with industry standard 8051
    • Pipeline RISC architecture enables to execute instructions 10 times faster than standard 8051
  • Up to 16MHz clock operation, @4.5~5.5*
  • Up to 8MHz clock operation, @ 2.7~5.5*
  • Up to 4MHz clock operation, @ 2.0~5.5*
• Memories
  • 128 bytes internal Data Memory (IDM) SRAM
  • 2K bytes EEPROM* with high endurance
    • Minimum 100,000 program/erase cycles
    • Minimum 10 years data retention
  • Programming lock level for software security
• Clock Management
  • Internal oscillator: 16MHz±2% @ 2.0V~5.5V
  • Crystal input with 4MHz~16MHz
• Power Management
  • 1 STOP mode for power saving
  • 1 IDLE mode for only peripheral operation
• Interrupt Management
  • Up to 9 interrupt sources
  • Up to 3 external interrupt sources
• Reset Management
  • Power On Reset (POR)
  • Low Voltage Reset (LVR)
    • Three trigger level(1.84V/2.5V/4.1V)
  • Pad Reset (PAD_RST)
  • Watchdog Reset (WDT_RST)
  • Software Reset (S/W_RST)
  • Stop Mode Reset (STOP_RST)
  • Miss Clock Reset (MISS_CLK_RST)
  • Flash Related Error Reset (FLASH_ERR_RST)
• Programmable Watchdog Timer
  • A time-base generator
  • An event timer
  • System supervisor
• I/O Ports
  • Max. 13 multifunction bi-directional I/Os
    • Each incorporate with pull-up resistor, pull-down resistor, output high, output low or floating input, depending on programmer's settings on the corresponding registers
    • I/O ports with 20mA current sink
    • I/O ports with 8mA current drive
  • One single output low I/O
    • with pull-up resistor, pull-down resistor, output low or floating input, depending on programmer's settings on the corresponding registers
    • I/O ports with 20mA current sink
• Two 16-bit Timer/Counter (Timer 0/1)
  • Timer mode with clock source selectable
  • Auto reload 8-bit timers
  • Externally gated event counters
• One Powerful Timer2 with 16-bit Compare/Capture Unit
  • Timer mode with clock source selectable
  • Auto-reload 16-bit timers
  • Externally gated event counters
  • Event capturing
  • Digital signals generator
  • Pulse width modulation and measurement
• UART0
  • One synchronous mode
  • Three asynchronous modes
• A/D converter
  • Up to 6+1 channel 12-bit resolution ADC
  • Max conversion clock: 2MHz (F_OSC /8) @16MHz
• Built-in Comparators
  • Two comparators with input offset < 10mV
  • Internal 4-bit reference voltage generator

*Note1: The lowest operating voltage is defined by the selection of LVR trigger level.
*Note2: The EEPROM memory can't be written at VDD<1.8V.