Products - GPM8F3364B

General Description

GPM8F3364B is a highly integrated microcontroller, which integrates a pipelined 1T 8051 CPU, 12K-byte external data memory(XRAM), 256-byte internal data memory(IDM) and 96K-byte program memory.  It supports up to 56 programmable multi-functional I/Os, Timer0/1, CCP0/1/2, UART0/1, 2 sets SPI (master/slaver), 2 sets I2C (master/slaver),1 set 8-bit current DAC , 2 sets analog comparator, 1 set real time counter, 1 set  64MHz PLL, 16-bit X 16-bit multiplier, 32-bit / 16-bit divider, 16-bit adder, 16-bit subtractor, 32-bit shifter and 1 set of 24 extend and 2 internal input channel SAR ADC with 12-bit resolution for general-purpose application.  GPM8F3364B operates with a wide range of working voltage that from 2.2V to 5.5V. For power saving, it provides a power management unit to manage the system power. Moreover, there is one on-chip debug circuit with two pins to facilitate full speed in-system debug.

Features

• CPU
  • High speed, high performance 1T 8051
• 100% software compatible with industry standard 8051
• Pipeline RISC architecture enables to execute instructions 10 times faster than standard 8051
• Up to 64MHz clock operation
• Memories
  • 12K bytes XRAM
  • 256 bytes internal Data Memory (IDM) SRAM
  • 96K bytes FLASH with high endurance
• Minimum 20K program/erase cycles
• Minimum 30us program time
• Minimum 30ms erase time
• Minimum 100 years data retention
• 1KB page size
• Flexible memory size for AP and ISP
• Memory protection mechanism for FLASH access
  • Programmable read-only level for software security
• Clock Management
  • Internal oscillator with 8MHz±2% @ 2V~5.5V
  • Internal oscillator with PLL : 64MHz @2.2~5.5V
  • Internal oscillator with 32KHz ± 50% @2.2~5.5V
  • Crystal input with 8MHz
  • Crystal input with 32KHz
• Power Management
  • One Sleep mode for power saving
• Interrupt Management
  • 22 interrupt sources
  • 6 wakeup source
  • Up to 7 external interrupt sources
  • Up to 16 keyboard interrupt sources
• Reset Management
  • Power On Reset (POR)
  • Low Voltage Reset (LVR)
  • Pad Reset (PAD_RST)
  • Watchdog Reset (WDT_RST)
  • Software Reset (S/W_RST)
  • FLASH Access Error Reset (ADDR_ERR_RST)
• Programmable Watchdog Timer
  • A time-base generator
  • An event timer
  • System supervisor
• I/O Ports
  • 56 multifunction bi-direction I/Os
  • Each incorporate with pull-up resistor, pull-down resistor, output high, output low , output driving capability and floating input which depending on programmer’s settings on the corresponding registers
  • I/O ports with 5mA current sink @VDD=3.3V
  • I/O ports with 6mA current drive@VDD=3.3V
• Two 16-bit Timer/Counter (Timer 0/1)
  • Timer mode with five source selectable
  • 13-bit/ 16-bit up-count timers
  • Auto reload 8-bit timers
  • Two 8-bit timers
  • Externally gated event counters
• UART0/1
  • One synchronous mode
  • Three asynchronous modes
• SPI0 /1 (master / slaver mode)
  • Programmable phase and polarity of master clock
  • Programmable master SPI clock frequency
  • Max SPI clock: 32MHz (F_pll /2) @64MHz
  • Programmable data transfer with CPU mode or DMA mode
• A/D Converter
  • 24 extended and 2 internal input channels of 12-bit resolution ADC
  • Max conversion rate@ 880K sps
  • Control independent per set
  • Programmable data transfer with CPU mode or DMA mode
  • Programmable A/D conversion data width
  • 8 sets of ADC_VREF voltage selection supported
• I2C0/1 (master / slaver mode)
  • Programmable master I2C clock frequency
  • Max I2C clock:500KHz (F_pll /128) @64MHz
• MDU
  • 16-bit X 16-bit signed multiplier
  • 32-bit / 16-bit signed divider
  • 16-bit + 16-bit signed adder.
  • 16-bit - 16-bit signed subtractor.
  • 32-bit arithmetic shifter.
• Key Change
  • Programmable 16 IOs key change interrupt
• Analog Comparator
  • Two analog comparators
  • 32-stage selection reference voltage
• DMA
  • One channel DMA supported
  • DMA path SPI RX to XRAM / SPI TX to XRAM / ADC to XRAM / XRAM to XRAM
• Current DAC
  • 8-bit current DAC supported
  • 4K~16KHz sampling frequency
  • Up to 4.5mA full scale output current with VDD= 5V
• RTC
  • Programmable real-time-counter wakeup source. 1 Hour/ 30mimute/ 60 second/ 1 second / halt second
• Three Powerful CCP 0/1/2 unit with 16-bit resolution (Compare / Capture / PWM Unit)
  • Timer mode with selectable clock source
  • Auto-reload 16-bit timers
  • Event capturing
  • Pulse width modulation
• Built-in Low Voltage Reset
  • Trigger level: 2.2V, 2.5V, 2.8V, 4V
• Built-in Low Voltage Detect
  • Programmable level: 2.4V, 2.7V, 3V, 3.3V, 3.6V , 3.9V , 4.2V , 4.5V
• On-chip Debug Unit
  • C compatible development tools